Latches, Catches and Hinges

Cam latches are commonly referred to as quarter-turn latches because they use a key, handle, or knob to turn the pawl 90 degrees to catch on the frame panel.

Metal Plates for Magnetic Catches provide a support to magnetically connect a catches. They come in various sizes and materials.

Adjustable Compression Latches are IP65 rated and are made from either Chrome or Black Powder Coated Die-Cast Zinc. They offer a 6mm compression and there are 3 cam styles available; either flat, offset or deep. The cam can be used forward or reversed and the latch provides good compression and noise isolation. The 2 fixing sizes available are 20.2mm x 22.2mm and 19.2mm x 22.2mmAdjustable Compression Latches w/Wing Knob are used for cabinets that require better sealing under vibration. The range comes in a choice of finish and are available in locking and non locking versions.

Concealed hinges are not visible from the outside of a door or panel and therefore provide a clean profile and tamper resistance.

For a low-cost easy-to-install solution, our rubber socket door holders consist of two parts – a male knob and a female socket – one side mounted to a wall and the other to the door. Opening the door and pushing the two mating parts together will hold the door open. We also carry steel and stainless door holders that will hold the door open at a specific angle and prevent it from opening too far.

Door Stops hold door open at specific angle and prevents door from opening too far. When door is open fully, catch will hold door in place. To release door, push open slightly and catch is released.

Draw latches use a lift-and-catch design to draw two items together using tension.

These pressure release latches provide venting in the event of internal explosion and maintain a seal in order to prevent loss of heat and/or escape of gasses under normal conditions. Latches have an adjustable strike and the release force is adjustable.

Made of acrylic, these flexible folding hinges have rigid sides that are permanently bonded to a flexible center section. Ideal for indoor or outdoor use. Sold in 48-inch lengths that can be easily cut to size.

Sealing Gaskets are clip on profiles offering edge protection and sealing. Essentially used on metal sheet, they offer protection from vibrations, ingress of humidity and dirt. They provide an additional seal to enclosure boxes.Simply push on exposed edges of metal, fiberglas, plastic, plywood or glass. Positive gripping locks trim in place. All products have a segmented metal core.Quick and efficient way to attach windows to frames. NEMA 12 rated safe for water and dust.

Contractor Pack is a closed cell blend of neoprene, nitrile, and PVC. It has excellent ozone and oxidation resistance, well suited for outdoor applications, and is cost effective for HVAC.

Screw on hasps offer ease of use by simply closing the latch and turning the knob to secure the door shut.

One Way Travel Drawer Slides are roller slides that are ideal for use in desks, cabinets, machine tool drawers, and similar applications. These brightly finished metal slides have a tight tolerance, smooth operation, and a smooth glide.

Two Way Travel Drawer Slides provide access from both sides of the installation with full extension from the center point for complete access to the contents. The hold-in detent at the center keeps conveyances in position until use and cannot be removed.

Kit can be used with any 5⁄16" square shanked handles for two point locking. Kit includes two gold zinc plated steel rods, two plastic rod guides, steel cam, two steel bushings, two wave washers, and three set screws. The Quarter Turn lock range is supplied with a range of accessories including fixing rings. These are supplied in two different types; one in Spring Steel and the other in Die Cast Zinc. They are suitable for all locks with a 20.2 x 22.2 fixing hole. These are quarter turn latch accessories. Available in 3 styles; 2 are latch hooks and 1 is a latch finger pull. Latch and Lock Keys are specific to their parent part for additional security and will often need to be ordered separately. All of the keys for our locks and latches are available here.

Free-swinging leaf hinges, also known as butt hinges, offer no resistance and consist of two flat plates joined by a pin through a center barrel.

Heavy Duty Telescopic Lid Stays are ideal for holding open lids, electric panel and inspection covers. They are suitable for heavy duty applications. The range offers left or right hand versions, and a choice of materials.Folding Lid Stays are ideal for holding open lids, electric panel and inspection covers. Can be used as left or right hand in a choice of materials.Folding Lid Stays are ideal for holding open lids, electric panel and inspection covers. The range offers left and right hand version in a choice of materials.

Lift-Off Hinge for Structural SystemsLift-Off Flag Hinges - Screw on are a two part rolled steel body with round end caps. Ideal for screw on frame for more industrial unitsMetal in-line Lift Off Hinges are easy lift off for flush mounted doors. They have a hinge rotation angle of 180 degree.Metal Offset Lift Off Hinges allows simple and quick door removal with an hinge rotation angle of 180 degree. Left and right hand available.Mini Metal In-Line Lift Off Hinges available for doors opening to the left. Metric uses M4 x 0.7 screws

Locking Paddle Latch with Right & Left LatchingProducts are flush mounting, available either all stainless steel or black powder coated with bright zinc plated slide. Maximum working load is 125lbs.Products are flush mounting, cup, paddle and cover are type 304 stainless steel. Slide is 1010 steel, chrome plated. Three grip ranges availabe. Maximum working load is 50 lbs.

T-Handles are used for applications where flush mounting is required. The range offered is essentially for heavy duty applications. Offered in locking styles.

Piano hinges, also called continuous hinges, run the entire length of a door or lid. They provide more stability than traditional hinges, making them ideal for heavier doors and lids that require extra support.

Flawless clarity for displays, food bins, and protective covers. Squeak-resistant nylon pin. Available in transparent, white, and black. Solvent cementable.

Locking flush ring-pull latches can be used in various applications. These are low profile, corrosion resistant latches that can be locked with a key to prevent the ring from moving.Non-locking flush ring-pull latches are low profile, corrosion resistant latches. Maximum working load is 60 lbs.

Shank latches have a T-shaped or L-shaped handle that turns the pawl to hook or unhook it from the frame panel.

Side Hinges offer a rotational angle of 180 degrees. Types 1 and 2 are high resistance hinges for medium and heavy door panels. They also offer high security and are assembled using the special screws provided. Type 3 is a lower cost lower security alternative