Carbon Steel

Works with all major screw types. The tools come as a set or individuals that feature a variety of sizes and are precision machined. They are designed to work in tight places without the added stress of drilling.

One piece Bonded Mounts provide multi-directional vibration isolation, shock attenuation, and noise reduction. These fail safe mounts are easy to install and provide consistent performance when used with recommended snubbing washers.Two Piece Bonded Mounts provide multi-directional vibration isolation, shock attenuation, and noise reduction. These fail safe mounts are easy to install and provide consistent performance when used with recommended snubbing washers.

Neoprene Compression Mounts protect against shock, vibration, and noise in horizontal or vertical compression load applications. These neoprene rubber mounts have metal inserts and plates that are best suited for use in compressors, motors, fans, and generators.

Eye bolts consist of a threaded shank with a loop at one end. When attached to structures such as wood or steel posts, rope or cable is fed through the loop to lift objects. Made of forged carbon steel or stainless steel, our selection of eye bolts includes plain style and shoulder style to resist bending. Available with a hex nut for additional support.

These wire lock pins have a pin and cotter in one assembly. The wire loop is pulled over the pin end to lock it in place or remove it. Eliminates cotter pin loss. Headed shank formed of carbon steel. Retainer wire formed of MB spring wire. Zinc plated.Self-locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Pin is carbon steel, heat-treated to Rockwell RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Manual Horizontal Hook & Latch Clamps operate on a horizontal plane allowing two faces to be fastened together on the same plane or at 90 degrees. These clamps have a low profile for applications having a height restriction.

With springs being such an integral part of power transmission applications, Reid Supply has about every kind of spring: compression springs, die springs, solid springs, drawbar springs, extension springs, torsion springs, etc.

Pad eyes have a similar function as eye bolts and eye nuts, but unlike their counterparts, pad eyes are welded in place to create a permanent fastening point. While some types are suited for lifting applications, they can also be used as tie downs or attachment points to connect slings and rigging hardware. Made of forged carbon steel or stainless steel.

Retainer Rings are installed into pre-manufactured grooves on axles to act as a shoulder and retain a specified component or assembly. These retainers are designed with a lip for easy assembly and dismantling.C-Clip Retainer Rings can be used on axles with or without pre-manufactured grooves as an ideal solution to shoulder and retain a specified component or assembly. These C-Clips have a durable and bright zinc finish.E-Clip Retainer Rings slide into a groove on a shaft to shoulder, align, and retain a specific component or assembly. E-Clips are available in a wide range of sizes and variety of materials to best suit your application.

Thrust bearings are designed for moderate speeds and fairly high loads. Reid Supply also offers economical nylon ball retainers and cylindrical rollers.

These check nuts are made of 303 stainless steel or low carbon steel, soft, with a black oxide finish. They can be used in conjunction with many other components such as knurled head screws, torque thumb screws, hand knob assemblies, toggle show clamp assemblies and many other tooling applications.

Turnbuckles are commonly used in rigging to apply tension and reduce slack in lengths of rope or cable. Our selection of carbon steel and stainless steel turnbuckles includes jaw-and-jaw, eye-and-eye, and hook-and-eye configurations.

Wire rope thimbles protect the eye or loop of wire rope assemblies from abrasion and deformation. They provide a solid barrier and sturdy structure to withstand damage to the cable strands from other rigging fittings.

Woodruff keys are shaped like a half circle and used to lock gears and pulleys to the drive shafts of machine tools and engines. The round edge of the key is designed to fit into the keyseat, which is a curved pocket on the shaft. The flat edge of the key remains exposed and fits into the keyway, which is a rectangular groove in the gear or pulley.